Bootstrak Skip to main content

3. Specification – Interfaces and Wiring

Streszczenie: Specyfikacja, część 1 – interfejsy: dla każdego z 16 modułów ST-1xxx opis panelu, schemat podłączenia łączników i czujników 2- i 3-przewodowych (opisany tekstem) oraz tabela przypisania pinów.
EN: Specification, part 1: front panel, wiring diagram (described in text) and pin assignment for each of the 16 ST-1xxx modules.

Dotyczy: moduły wejść cyfrowych CREVIS serii ST-1xxx systemu FnIO (4, 8 i 16 wejść; 5, 12/24, 48 Vdc oraz 110/220 Vac)
Źródło: dokumentacja producenta (CREVIS ST-1xxx Digital Input Modules User Manual); tabele przepisane z obrazów na tekst, opisy rysunków – opracowanie Multiprojekt

Rozdział 3 „Specification” podzielono na 2 strony: Interfaces and Wiring · Technical Data.

3.1.1 The Interface


3.1.1.1 ST-1114 

image.png

image.pngDiagram: ST-1114 – terminals and wiring of input switches and sensors

Diagram description (text version): ST-1114 (4 inputs, sink/positive logic, 5 Vdc): front view with FnBus contacts on the left side, STATUS LED and channel LEDs 0–3, and the 8-pin terminal block. Input switches are connected between the inputs (pins 0–3) and +5 V (pins 6/7); pins 4/5 are field ground 0 V. The wiring diagram shows a 2-wire sensor connected between CH1 and 5 V and a 3-wire sensor connected to CH2, 0 V and 5 V. System power (5 V, GND) and the FnBus signal come from the FnBus contacts; field power (0 Vdc / 5 Vdc) is taken from the field power contacts.

ST-1114 – pin description

Pin No.Description
0Input Channel 0
1Input Channel 1
2Input Channel 2
3Input Channel 3
4Field Ground (0V)
5Field Ground (0V)
6Field Power (+5Vdc)
7Field Power (+5Vdc)

3.1.2.2 ST-111F

image.png

image.pngDiagram: ST-111F – 20-pin connector and input wiring

Diagram description (text version): ST-111F (16 inputs, sink/positive logic, 5 V): front view with FnBus contacts (system power 5 V/GND and FnBus signal), STATUS LED, 16 channel LEDs and a 20-pin connector for I/O and power wiring. Connector pinout: pins 1–16 – inputs CH0–CH15 (odd pins CH0, CH2 … CH14, even pins CH1, CH3 … CH15), pins 17/18 – 0 V, pins 19/20 – 5 V. Each input is wired through a switch to the common line, which is connected to 5 V (pins 19/20). The field power contacts at the bottom of the module are labelled Field Power (0 Vdc) and Field Power (24 Vdc) in the drawing.

ST-111F – pin description

Pin No.Description
1Input Channel 0
2Input Channel 1
3Input Channel 2
4Input Channel 3
5Input Channel 4
6Input Channel 5
7Input Channel 6
8Input Channel 7
9Input Channel 8
10Input Channel 9
11Input Channel 10
12Input Channel 11
13Input Channel 12
14Input Channel 13
15Input Channel 14
16Input Channel 15
17Field Ground (0V)
18Field Ground (0V)
19Field Power (+5Vdc)
20Field Power (+5Vdc)

3.1.3.3 ST-1124

image.png

image.pngDiagram: ST-1124 – terminals and wiring of input switches and sensors

3.1.4.Diagram description (text version): ST-112F

1124

image.png

(4

image.png

inputs,

source/negative logic, 5 V): front view with FnBus contacts on the left side, STATUS LED, channel LEDs 0–3 and the 8-pin terminal block. Input switches are connected between the inputs (pins 0–3) and 0 V (pins 4/5); pins 6/7 are field power +5 V. The wiring diagram shows a 2-wire sensor between CH1 and 0 V, and a 3-wire sensor connected to CH2, 0 V and 5 V. System power (5 V, GND) and the FnBus signal come from the FnBus contacts; field power is taken from the field power contacts.

3.1.5.ST-1124 ST-1214– pin description

image.png

Pin No.Description
0Input Channel 0
1Input Channel 1
2Input Channel 2
3Input Channel 3
4Field Ground (0V)
5Field Ground (0V)
6Field Power (+5Vdc)
7Field Power (+5Vdc)

3.1.4 ST-112F

image.pngDiagram: ST-112F – 20-pin connector and input wiring

3.1.6.Diagram description (text version): ST-1218112F (16 inputs, source/negative logic, 5 V): front view with FnBus contacts (system power 5 V/GND and FnBus signal), STATUS LED, 16 channel LEDs and a 20-pin connector for I/O and power wiring. Connector pinout: pins 1–16 – inputs CH0–CH15 (odd pins CH0, CH2 … CH14, even pins CH1, CH3 … CH15), pins 17/18 – 0 V, pins 19/20 – 5 V. Each input is wired through a switch to the common line, which is connected to 0 V (pins 17/18). Field power contacts: 0 Vdc and 5 Vdc.

ST-112F – pin description

image.png

Pin No.Description
1Input Channel 0
2Input Channel 1
3Input Channel 2
4Input Channel 3
5Input Channel 4
6Input Channel 5
7Input Channel 6
8Input Channel 7
9Input Channel 8
10Input Channel 9
11Input Channel 10
12Input Channel 11
13Input Channel 12
14Input Channel 13
15Input Channel 14
16Input Channel 15
17Field Ground (0V)
18Field Ground (0V)
19Field Power (+5Vdc)
20Field Power (+5Vdc)

3.1.5 ST-1214

image.pngDiagram: ST-1214 – terminals and wiring of input switches and sensors

3.1.7.Diagram description (text version): ST-121F1214 (4 inputs, sink/positive logic, 24 V): front view with FnBus contacts on the left side, STATUS LED, channel LEDs 0–3 and the 8-pin terminal block. Input switches are connected between the inputs (pins 0–3) and +24 V (pins 6/7); pins 4/5 are field ground 0 V. The wiring diagram shows a 2-wire sensor between CH1 and 24 V, and a 3-wire sensor connected to CH2, 0 V and 24 V. System power (5 V, GND) and the FnBus signal come from the FnBus contacts; field power is taken from the field power contacts.

ST-1214 – pin description

image.png

Pin No.Description
0Input Channel 0
1Input Channel 1
2Input Channel 2
3Input Channel 3
4Field Ground (0V)
5Field Ground (0V)
6Field Power (+24Vdc)
7Field Power (+24Vdc)

3.1.6 ST-1218

image.pngDiagram: ST-1218 – terminals and wiring of input switches and sensors

3.1.8.Diagram description (text version): ST-1224

1218

image.png

(8

image.png

inputs,

sink/positive logic, 24 V): front view with FnBus contacts (system power 5 V/GND and FnBus signal), STATUS LED, channel LEDs 0–7 and the 8-pin terminal block, where all pins 0–7 are inputs CH0–CH7 (no supply terminals on the module). The input switches are connected to an external 24 V line; the wiring diagram shows a 2-wire sensor between CH1 and the 24 V line, and a 3-wire sensor connected to CH2 and to the external 24 V and 0 V lines. Field power contacts: 0 Vdc and 24 Vdc.

3.1.9.ST-1218 ST-1228– pin description

image.png

Pin No.Description
0Input Channel 0
1Input Channel 1
2Input Channel 2
3Input Channel 3
4Input Channel 4
5Input Channel 5
6Input Channel 6
7Input Channel 7

3.1.7 ST-121F

image.png

 

3.1.10. ST-122F

image.png

image.pngDiagram: ST-121F – 20-pin connector and input wiring

3.1.11.Diagram description (text version): ST-1314121F (16 inputs, sink/positive logic, 24 V): front view with FnBus contacts (system power 5 V/GND and FnBus signal), STATUS LED, 16 channel LEDs and a 20-pin connector for I/O and power wiring. Connector pinout: pins 1–16 – inputs CH0–CH15 (odd pins CH0, CH2 … CH14, even pins CH1, CH3 … CH15), pins 17/18 – 0 V, pins 19/20 – 24 V. Each input is wired through a switch to the common line, which is connected to 24 V (pins 19/20). Field power contacts: 0 Vdc and 24 Vdc.

ST-121F – pin description

image.png

Pin No.Description
1Input Channel 0
2Input Channel 1
3Input Channel 2
4Input Channel 3
5Input Channel 4
6Input Channel 5
7Input Channel 6
8Input Channel 7
9Input Channel 8
10Input Channel 9
11Input Channel 10
12Input Channel 11
13Input Channel 12
14Input Channel 13
15Input Channel 14
16Input Channel 15
17Field Ground (0V)
18Field Ground (0V)
19Field Power (+24Vdc)
20Field Power (+24Vdc)

3.1.8 ST-1224

image.pngDiagram: ST-1224 – terminals and wiring of input switches and sensors

3.1.12.Diagram description (text version): ST-131F1224 (4 inputs, source/negative logic, 24 V): front view with FnBus contacts on the left side, STATUS LED, channel LEDs 0–3 and the 8-pin terminal block. Input switches are connected between the inputs (pins 0–3) and 0 V (pins 4/5); pins 6/7 are field power +24 V. The wiring diagram shows a 2-wire sensor between CH1 and 0 V, and a 3-wire sensor connected to CH2, 0 V and 24 V. System power (5 V, GND) and the FnBus signal come from the FnBus contacts; field power is taken from the field power contacts.

ST-1224 – pin description

image.png

Pin No.Description
0Input Channel 0
1Input Channel 1
2Input Channel 2
3Input Channel 3
4Field Ground (0V)
5Field Ground (0V)
6Field Power (+24Vdc)
7Field Power (+24Vdc)

3.1.9 ST-1228

image.pngDiagram: ST-1228 – terminals and wiring of input switches and sensors

3.1.13.Diagram description (text version): ST-13241228 (8 inputs, source/negative logic, 24 V): front view with FnBus contacts (system power 5 V/GND and FnBus signal), STATUS LED, channel LEDs 0–7 and the 8-pin terminal block, where all pins 0–7 are inputs CH0–CH7 (no supply terminals on the module). The input switches are connected to an external 0 V line; the wiring diagram shows a 2-wire sensor between CH1 and the 0 V line, and a 3-wire sensor connected to CH2 and to the external 24 V and 0 V lines. Field power contacts: 0 Vdc and 24 Vdc.

ST-1228 – pin description

image.png

Pin No.Description
0Input Channel 0
1Input Channel 1
2Input Channel 2
3Input Channel 3
4Input Channel 4
5Input Channel 5
6Input Channel 6
7Input Channel 7

3.1.10 ST-122F

image.pngDiagram: ST-122F – 20-pin connector and input wiring

3.1.14.Diagram description (text version): ST-132F122F (16 inputs, source/negative logic, 24 V): front view with FnBus contacts (system power 5 V/GND and FnBus signal), STATUS LED, 16 channel LEDs and a 20-pin connector for I/O and power wiring. Connector pinout: pins 1–16 – inputs CH0–CH15 (odd pins CH0, CH2 … CH14, even pins CH1, CH3 … CH15), pins 17/18 – 0 V, pins 19/20 – 24 V. Each input is wired through a switch to the common line, which is connected to 0 V (pins 17/18). Field power contacts: 0 Vdc and 24 Vdc.

ST-122F – pin description

image.png

Pin No.Description
1Input Channel 0
2Input Channel 1
3Input Channel 2
4Input Channel 3
5Input Channel 4
6Input Channel 5
7Input Channel 6
8Input Channel 7
9Input Channel 8
10Input Channel 9
11Input Channel 10
12Input Channel 11
13Input Channel 12
14Input Channel 13
15Input Channel 14
16Input Channel 15
17Field Ground (0V)
18Field Ground (0V)
19Field Power (+24Vdc)
20Field Power (+24Vdc)

3.1.11 ST-1314

image.pngDiagram: ST-1314 – terminals and wiring of input switches and sensors

3.1.15.Diagram description (text version): ST-18041314 (4 inputs, sink/positive logic, 48 V): front view with FnBus contacts on the left side, STATUS LED, channel LEDs 0–3 and the 8-pin terminal block. Input switches are connected between the inputs (pins 0–3) and +48 V (pins 6/7); pins 4/5 are field ground 0 V. The wiring diagram shows a 2-wire sensor between CH1 and 48 V, and a 3-wire sensor connected to CH2, 0 V and 48 V. System power (5 V, GND) and the FnBus signal come from the FnBus contacts; field power is taken from the field power contacts.

ST-1314 – pin description

image.png

Pin No.Description
0Input Channel 0
1Input Channel 1
2Input Channel 2
3Input Channel 3
4Field Ground (0V)
5Field Ground (0V)
6Field Power (+48Vdc)
7Field Power (+48Vdc)

3.1.12 ST-131F

image.pngDiagram: ST-131F – 20-pin connector and input wiring

3.1.16.Diagram description (text version): ST-1904

131F

image.png

(16

image.png

inputs,

sink/positive logic, 48 V): front view with FnBus contacts (system power 5 V/GND and FnBus signal), STATUS LED, 16 channel LEDs and a 20-pin connector for I/O and power wiring. Connector pinout: pins 1–16 – inputs CH0–CH15 (odd pins CH0, CH2 … CH14, even pins CH1, CH3 … CH15), pins 17/18 – 0 V, pins 19/20 – 48 V. Each input is wired through a switch to the common line, which is connected to 48 V (pins 19/20). Field power contacts: 0 Vdc and 48 Vdc.

3.2.ST-131F Environment– Specificationpin description

image.png

Pin

No.

Description
1Input Channel

3.3.0

2Input SpecificationChannel
3.1
3Input Channel 2
4Input Channel 3
5Input Channel 4
6Input Channel 5
7Input Channel 6
8Input Channel 7
9Input Channel 8
10Input Channel 9
11Input Channel 10
12Input Channel 11
13Input Channel 12
14Input Channel 13
15Input Channel 14
16Input Channel 15
17Field Ground (0V)
18Field Ground (0V)
19Field Power (+48Vdc)
20Field Power (+48Vdc)

3.1.13 ST-1114 1324

image.png

 

3.3.2. ST-111F

image.pngDiagram: ST-1324 – terminals and wiring of input switches and sensors

3.3.3.Diagram description (text version): ST-11241324 (4 inputs, source/negative logic, 48 V): front view with FnBus contacts on the left side, STATUS LED, channel LEDs 0–3 and the 8-pin terminal block. Input switches are connected between the inputs (pins 0–3) and 0 V (pins 4/5); pins 6/7 are field power +48 V. The wiring diagram shows a 2-wire sensor between CH1 and 0 V, and a 3-wire sensor connected to CH2, 0 V and 48 V. System power (5 V, GND) and the FnBus signal come from the FnBus contacts; field power is taken from the field power contacts.

ST-1324 – pin description

Pin No.Description
0Input Channel 0
1Input Channel 1
2Input Channel 2
3Input Channel 3
4Field Ground (0V)
5Field Ground (0V)
6Field Power (+48Vdc)
7Field Power (+48Vdc)

3.1.14 ST-132F

image.pngDiagram: ST-132F – 20-pin connector and input wiring

3.3.4.Diagram description (text version): ST-112F132F (16 inputs, source/negative logic, 48 V): front view with FnBus contacts (system power 5 V/GND and FnBus signal), STATUS LED, 16 channel LEDs and a 20-pin connector for I/O and power wiring. Connector pinout: pins 1–16 – inputs CH0–CH15 (odd pins CH0, CH2 … CH14, even pins CH1, CH3 … CH15), pins 17/18 – 0 V, pins 19/20 – 48 V. Each input is wired through a switch to the common line, which is connected to 0 V (pins 17/18). Field power contacts: 0 Vdc and 48 Vdc.

ST-132F – pin description

Pin No.Description
1Input Channel 0
2Input Channel 1
3Input Channel 2
4Input Channel 3
5Input Channel 4
6Input Channel 5
7Input Channel 6
8Input Channel 7
9Input Channel 8
10Input Channel 9
11Input Channel 10
12Input Channel 11
13Input Channel 12
14Input Channel 13
15Input Channel 14
16Input Channel 15
17Field Ground (0V)
18Field Ground (0V)
19Field Power (+48Vdc)
20Field Power (+48Vdc)

3.1.15 ST-1804

image.pngDiagram: ST-1804 – terminals and wiring of 110 Vac inputs

3.3.5.Diagram description (text version): ST-1214

1804

image.png

(4

inputs, 110 Vac AC): front view with FnBus contacts (system power 5 V/GND and FnBus signal), STATUS LED, channel LEDs 0–3 and the 8-pin terminal block. Pins 0–3 are inputs CH0–CH3, pins 4/5 – L1 110 Vac, pins 6/7 – L2 110 Vac. The input switches are connected between the inputs and L2 (pins 6/7); the wiring diagram shows a 2-wire sensor between CH1 and L2. The field power contacts carry L1 and L2 110 Vac.

3.3.6.ST-1804 ST-1218– pin description

Pin No.Description
0Input Channel 0
1Input Channel 1
2Input Channel 2
3Input Channel 3
4L1
5L1
6L2
7L2

3.1.16 ST-1904

image.pngDiagram: ST-1904 – terminals and wiring of 220 Vac inputs

3.3.7.Diagram description (text version): ST-121F1904

(4

image.pnginputs, 220 Vac AC): front view with FnBus contacts (system power 5 V/GND and FnBus signal), STATUS LED, channel LEDs 0–3 and the 8-pin terminal block. Pins 0–3 are inputs CH0–CH3, pins 4/5 – L1 220 Vac, pins 6/7 – L2 220 Vac. The input switches are connected between the inputs and L2 (pins 6/7); the wiring diagram shows a 2-wire sensor between CH1 and L2. The field power contacts carry L1 and L2 220 Vac.

3.3.8.ST-1904 ST-1224– pin description

Pin No.Description
0Input Channel 0
1Input Channel 1
2Input Channel 2
3Input Channel 3
4L1
5L1
6L2
7L2

Słowa kluczowe

image.pngschemat podłączenia, przypisanie pinów, zaciski, złącze 20-pin, czujnik 2-przewodowy, czujnik 3-przewodowy, sink, source, field power, FnBus

3.3.9. ST-1228

image.png

3.3.10. ST-122F

image.png

3.3.11. ST-1314 

image.png

3.3.12. ST-131F

image.png

3.3.13. ST-1324

image.png

3.3.14. ST-132F

image.png

3.3.15. ST-1804

image.png

3.3.16. ST-1904 

image.png