5. Function Parameter List – Part 2 (P5–P9)
Streszczenie: Tabela parametrów funkcyjnych KE600 (część 2 z 3): grupy P5–P9 (wyjścia, start/stop, panel, funkcje rozszerzone, zabezpieczenia) – zakresy nastaw, wartości fabryczne i możliwość zmiany.
EN: KE600 function parameter list (part 2 of 3): groups P5–P9 (outputs, start/stop, keypad, enhanced functions, protections) – setting ranges, factory defaults and modification attributes.
Dotyczy: falownik wektorowy z zamkniętą pętlą Micno KE600 (zasilanie 3AC 220 V, 3AC 380 V, 3AC 660 V; moce 1,5–630 kW)
Źródło: dokumentacja producenta (Micno KE600 Series Inverter User Manual); tabele przepisane z obrazów na tekst – opracowanie Multiprojekt
Nawigacja: część 2 z 3 · poprzednia: ← Part 1 (P0–P4) · następna: Part 3 (PA–A2, U0) →
5.1 Basic Function Parameter Table (Continued)
Kolumna „Modify”: ○ – parameter can be modified in stop and running status; ◎ – cannot be modified in running status; ● – actual detected value, cannot be modified.
P5 Group: Output Terminal
| Function code | Name | Detailed instruction | Factory default | Modify |
|---|---|---|---|---|
| P5-00 | HDO terminal output mode selection | 0: High speed pulse output 1: Open collector output | 0 | ○ |
| P5-01 | HDO open collector output selection | 0: No output 1: Inverter is running 2: Fault output (fault stop) 3: FDT1 output 4: Frequency arrival 5: Zero-speed running (no output when stop) 6: Motor overload pre-alarm 7: Inverter overload pre-alarm 8: Setting count value arrival 9: Designated count value arrival 10: Length arrival 11: PLC loop completed 12: Accumulated running time arrival 13: Frequency limiting 14: Torque limiting 15: Ready for running 16: AI1 > AI2 17: Frequency upper limit arrival 18: Frequency lower limit arrival 19: Under voltage status output 20: Communication setting 21: Orientation finished (reserved) 22: Orientation approach (reserved) 23: Zero-speed running 2 (output when stop) 24: Accumulated power-on time arrival 25: FDT2 output 26: Frequency 1 arrival output 27: Frequency 2 arrival output 28: Current 1 arrival output 29: Current 2 arrival output 30: Timing arrival output 31: AI1 input over limit 32: Off load 33: Reverse running 34: Zero-current status 35: Module temperature arrival 36: Output current over limit 37: Lower limit frequency arrival (output when stop) 38: Warning output (keep running) 39: Motor over temperature pre-alarm 40: This running time arrival 41: Reserved | 0 | ○ |
| P5-02 | Relay T1 output selection | Same as P5-01 (DO functions 0 ~ 41) | 2 | ○ |
| P5-03 | Relay T2 output selection | Same as P5-01 (DO functions 0 ~ 41) | 0 | ○ |
| P5-04 | Y1 output selection | Same as P5-01 (DO functions 0 ~ 41) | 0 | ○ |
| P5-05 | Y2 output selection | Same as P5-01 (DO functions 0 ~ 41) | 0 | ○ |
| P5-06 | HDO function selection | 0: Running frequency 1: Setting frequency 2: Output current 3: Output torque 4: Output power 5: Output voltage 6: Pulse input 7: AI1 8: AI2 9: Reserved 10: Length 11: Count value 12: Communication 13: Motor speed 14: Output current (100.0% corresponds to 1000.0A) 15: Output voltage (100.0% corresponds to 1000.0V) 16: Reserved | 0 | ○ |
| P5-07 | AO1 output function selection | Same as P5-06 (functions 0 ~ 16) | 0 | ○ |
| P5-08 | AO2 output function selection | Same as P5-06 (functions 0 ~ 16) | 0 | ○ |
| P5-09 | HDO output maximum frequency | 0.01kHz ~ 100.00kHz | 50.00kHz | ○ |
| P5-10 | AO1 offset coefficient | -100.0% ~ +100.0% | 0.0% | ○ |
| P5-11 | AO1 gain | -10.00 ~ +10.00 | 1.00 | ○ |
| P5-12 | AO2 offset coefficient | -100.0% ~ +100.0% | 0.0% | ○ |
| P5-13 | AO2 gain | -10.00 ~ +10.00 | 1.00 | ○ |
| P5-17 | HDO open collector output delay time | 0.0s ~ 3600.0s | 0.0s | ○ |
| P5-18 | Relay 1 output delay time | 0.0s ~ 3600.0s | 0.0s | ○ |
| P5-19 | Relay 2 output delay time | 0.0s ~ 3600.0s | 0.0s | ○ |
| P5-20 | Y1 output delay time | 0.0s ~ 3600.0s | 0.0s | ○ |
| P5-21 | Y2 output delay time | 0.0s ~ 3600.0s | 0.0s | ○ |
| P5-22 | Output terminal valid status selection | 0: Positive logic 1: Negative logic Units place: HDO Tens place: Relay 1 Hundreds place: Relay 2 Thousands place: Y1 Ten thousands place: Y2 | 00000 | ○ |
P6 Group: Start and Stop Control
| Function code | Name | Detailed instruction | Factory default | Modify |
|---|---|---|---|---|
| P6-00 | Start mode | 0: Direct start 1: Speed tracking and restart 2: Pre-excitation start | 0 | ○ |
| P6-01 | Speed tracking mode | 0: Begin from stop frequency 1: Begin from zero speed 2: Begin from maximum frequency | 0 | ◎ |
| P6-02 | Speed tracking speed | 1 ~ 100 | 20 | ○ |
| P6-03 | Start frequency | 0.00Hz ~ 10.00Hz | 0.00Hz | ○ |
| P6-04 | Start frequency holding time | 0.0s ~ 100.0s | 0.0s | ◎ |
| P6-05 | DC braking current before start/pre-excitation current | 0% ~ 100% | 0% | ◎ |
| P6-06 | DC braking time before start/pre-excitation time | 0.0s ~ 100.0s | 0.0s | ◎ |
| P6-07 | ACC/DEC mode | 0: Linear ACC/DEC 1: S-curve ACC/DEC A 2: S-curve ACC/DEC B | 0 | ◎ |
| P6-08 | Time of S curve's start part | 0.0% ~ (100.0% − P6-09) | 30.0% | ◎ |
| P6-09 | Time of S curve's end part | 0.0% ~ (100.0% − P6-08) | 30.0% | ◎ |
| P6-10 | Stop mode | 0: Deceleration to stop 1: Coast to stop | 0 | ○ |
| P6-11 | DC braking start frequency after stop | 0.00Hz ~ P0-10 (maximum frequency) | 0.00Hz | ○ |
| P6-12 | DC braking delay time after stop | 0.0s ~ 100.0s | 0.0s | ○ |
| P6-13 | DC braking current after stop | 0% ~ 100% | 0% | ○ |
| P6-14 | DC braking time after stop | 0.0s ~ 100.0s | 0.0s | ○ |
| P6-15 | Braking usage ratio | 0% ~ 100% | 100% | ○ |
P7 Group: Keypad and Display
| Function code | Name | Detailed instruction | Factory default | Modify |
|---|---|---|---|---|
| P7-00 | Inverter rated power | 0.1kW ~ 1000.0kW | Model dependent | ● |
| P7-01 | QUICK/JOG function selection | 0: Invalid 1: Switching between keypad command and remote command (terminal command and communication command) 2: FWD/REV switching 3: Forward jog 4: Reverse jog | 0 | ◎ |
| P7-02 | STOP/RST function selection | 0: Valid when keypad control 1: Always valid | 1 | ○ |
| P7-03 | Running status display 1 | 0000 ~ FFFF Bit00: Running frequency 1 (Hz) Bit01: Setting frequency (Hz) Bit02: Bus voltage (V) Bit03: Output voltage (V) Bit04: Output current (A) Bit05: Output power (kW) Bit06: Output torque (%) Bit07: DI status Bit08: DO status Bit09: AI1 voltage (V) Bit10: AI2 voltage (V) Bit11: Radiator temperature Bit12: Count value Bit13: Length value Bit14: Load speed display Bit15: PID setting | 81F | ○ |
| P7-04 | Running status display 2 | 0000 ~ FFFF Bit00: PID feedback Bit01: PLC step Bit02: HDI input pulse frequency (kHz) Bit03: Running frequency 2 (Hz) Bit04: Remain running time Bit05: AI1 voltage before calibration (V) Bit06: AI2 voltage before calibration (V) Bit07: Reserved Bit08: Linear speed Bit09: Current power-on time (hour) Bit10: Current running time (min) Bit11: HDI input pulse frequency (Hz) Bit12: Communication setting value Bit13: Reserved Bit14: Main frequency A display (Hz) Bit15: Auxiliary frequency B display (Hz) | 0 | ○ |
| P7-05 | Stop status display | 0000 ~ FFFF Bit00: Setting frequency (Hz) Bit01: Bus voltage (V) Bit02: DI input status Bit03: DO output status Bit04: AI1 voltage (V) Bit05: AI2 voltage (V) Bit06: Radiator temperature Bit07: Count value Bit08: Length value Bit09: PLC step Bit10: Load speed Bit11: PID setting Bit12: HDI input pulse frequency (kHz) | 73 | ○ |
| P7-06 | Load speed display coefficient | 0.0001 ~ 6.5000 | 3.0000 | ○ |
| P7-07 | IGBT module temperature | 0.0 °C ~ 100.0 °C | – | ● |
| P7-08 | Inverter rated voltage | 1V ~ 2000V | Model dependent | ● |
| P7-09 | Accumulated running time | 0h ~ 65535h | – | ● |
| P7-10 | Model No. | – | – | ● |
| P7-11 | Software version No. | – | – | ● |
| P7-12 | Load speed display decimal place | 0: 0 decimal place 1: 1 decimal place 2: 2 decimal places 3: 3 decimal places | 1 | ○ |
| P7-13 | Accumulated power-on time | 0h ~ 65535h | – | ● |
| P7-14 | Accumulated power consumption | 0kW ~ 65535kW | – | ● |
P8 Group: Enhanced Function
| Function code | Name | Detailed instruction | Factory default | Modify |
|---|---|---|---|---|
| P8-00 | Jog running frequency | 0.00Hz ~ P0-10 (max. frequency) | 2.00Hz | ○ |
| P8-01 | Jog acceleration time | 0.1s ~ 3600.0s | 20.0s | ○ |
| P8-02 | Jog deceleration time | 0.1s ~ 3600.0s | 20.0s | ○ |
| P8-03 | Acceleration time 2 | 0.1s ~ 3600.0s | Model dependent | ○ |
| P8-04 | Deceleration time 2 | 0.1s ~ 3600.0s | Model dependent | ○ |
| P8-05 | Acceleration time 3 | 0.1s ~ 3600.0s | Model dependent | ○ |
| P8-06 | Deceleration time 3 | 0.1s ~ 3600.0s | Model dependent | ○ |
| P8-07 | Acceleration time 4 | 0.1s ~ 3600.0s | Model dependent | ○ |
| P8-08 | Deceleration time 4 | 0.1s ~ 3600.0s | Model dependent | ○ |
| P8-09 | Jump frequency 1 | 0.00Hz ~ P0-10 (maximum frequency) | 0.00Hz | ○ |
| P8-10 | Jump frequency 2 | 0.00Hz ~ P0-10 (maximum frequency) | 0.00Hz | ○ |
| P8-11 | Jump frequency amplitude | 0.00Hz ~ P0-10 (maximum frequency) | 0.01Hz | ○ |
| P8-12 | FWD/REV dead time | 0.0s ~ 3600.0s | 0.0s | ○ |
| P8-13 | Reverse control | 0: Enable 1: Disable | 0 | ○ |
| P8-14 | Action when setting frequency lower than frequency lower limit | 0: Running at frequency lower limit 1: Stop 2: Zero-speed running | 0 | ○ |
| P8-15 | Droop control | 0.00Hz ~ 10.00Hz | 0.00Hz | ○ |
| P8-16 | Accumulated power-on arrival time | 0h ~ 36000h | 0h | ○ |
| P8-17 | Accumulated running arrival time | 0h ~ 36000h | 0h | ○ |
| P8-18 | Power-on running command valid protection selection | 0: No protection 1: Protection | 0 | ○ |
| P8-19 | Frequency detection target (FDT1) | 0.00Hz ~ P0-10 (maximum frequency) | 50.00Hz | ○ |
| P8-20 | Frequency detection lagging value (FDT1) | 0.0% ~ 100.0% (FDT1 level) | 5.0% | ○ |
| P8-21 | Frequency arrival detection amplitude | 0.0% ~ 100.0% (maximum frequency) | 0.0% | ○ |
| P8-22 | Jump frequency control during ACC/DEC | 0: Invalid 1: Valid | 0 | ○ |
| P8-25 | Acceleration time 1 and acceleration time 2 switching frequency point | 0.00Hz ~ P0-10 (maximum frequency) | 0.00Hz | ○ |
| P8-26 | Deceleration time 1 and deceleration time 2 switching frequency point | 0.00Hz ~ P0-10 (maximum frequency) | 0.00Hz | ○ |
| P8-27 | Terminal jog priority | 0: Invalid 1: Valid | 0 | ○ |
| P8-28 | Frequency detection target (FDT2) | 0.00Hz ~ P0-10 (maximum frequency) | 50.00Hz | ○ |
| P8-29 | Frequency detection lagging value (FDT2) | 0.0% ~ 100.0% (FDT2 level) | 5.0% | ○ |
| P8-30 | Any arrival frequency detection target 1 | 0.00Hz ~ P0-10 (maximum frequency) | 50.00Hz | ○ |
| P8-31 | Any arrival frequency detection amplitude 1 | 0.0% ~ 100.0% (maximum frequency) | 0.0% | ○ |
| P8-32 | Any arrival frequency detection target 2 | 0.00Hz ~ P0-10 (maximum frequency) | 50.00Hz | ○ |
| P8-33 | Any arrival frequency detection amplitude 2 | 0.0% ~ 100.0% (maximum frequency) | 0.0% | ○ |
| P8-34 | Zero-current detection level | 0.0% ~ 300.0% 100.0% corresponds to motor rated current | 5.0% | ○ |
| P8-35 | Zero-current detection delay time | 0.01s ~ 360.00s | 0.10s | ○ |
| P8-36 | Output current over limit value | 0.0% (no detection) 0.1% ~ 300.0% (motor rated current) | 200.0% | ○ |
| P8-37 | Output current over limit detection delay time | 0.00s ~ 360.00s | 0.00s | ○ |
| P8-38 | Any arrival current 1 | 0.0% ~ 300.0% (motor rated current) | 100.0% | ○ |
| P8-39 | Any arrival current 1 amplitude | 0.0% ~ 300.0% (motor rated current) | 0.0% | ○ |
| P8-40 | Any arrival current 2 | 0.0% ~ 300.0% (motor rated current) | 100.0% | ○ |
| P8-41 | Any arrival current 2 amplitude | 0.0% ~ 300.0% (motor rated current) | 0.0% | ○ |
| P8-42 | Timing function selection | 0: Invalid 1: Valid | 0 | ○ |
| P8-43 | Timing running time selection | 0: P8-44 1: AI1 2: AI2 3: Keypad potentiometer Analog input scale corresponds to F8-44 (i.e. P8-44) | 0 | ○ |
| P8-44 | Timing running time | 0.0 min ~ 3600.0 min | 0.0 min | ○ |
| P8-45 | AI1 input voltage protection lower limit | 0.00V ~ P8-46 | 3.10V | ○ |
| P8-46 | AI1 input voltage protection upper limit | P8-45 ~ 10.00V | 6.80V | ○ |
| P8-47 | Module temperature arrival | 0 °C ~ 100 °C | 75 °C | ○ |
| P8-48 | Cooling fan control | 0: Fan runs when inverter running 1: Fan always runs | 0 | ○ |
| P8-49 | Wake up frequency | 0.0 ~ PA-04 (PID given feedback range) | 3.0 | ○ |
| P8-50 | Wake up delay time | 0.0s ~ 3600.0s | 0.0s | ○ |
| P8-51 | Dormancy frequency | 0.00Hz ~ P0-10 (maximum frequency) | 0.00Hz | ○ |
| P8-52 | Dormancy delay time | 0.0s ~ 3600.0s | 0.0s | ○ |
| P8-53 | Running arrival time setting | 0.0 min ~ 3600.0 min | 0.0 min | ○ |
P9 Group: Fault and Protection
| Function code | Name | Detailed instruction | Factory default | Modify |
|---|---|---|---|---|
| P9-00 | Motor overload protection selection | 0: Disable 1: Enable | 1 | ○ |
| P9-01 | Motor overload protection gain | 0.20 ~ 10.00 | 1.00 | ○ |
| P9-02 | Motor overload pre-alarm coefficient | 50% ~ 100% | 80% | ○ |
| P9-03 | Stall over-voltage gain | 0 ~ 100 | 0 | ○ |
| P9-04 | Stall over-voltage point / braking threshold | 120% ~ 150% | 130% | ○ |
| P9-05 | Stall over current gain | 1 ~ 100 | 20 | ○ |
| P9-06 | Stall over-current point | 100% ~ 200% | 160% | ○ |
| P9-07 | Short-circuit to ground protection selection when power-on | 0: Invalid 1: Valid | 1 | ○ |
| P9-08 | Fast current limitation | 0: Disable 1: Enable | 1 | ○ |
| P9-09 | Fault auto reset times | 0 ~ 5 | 0 | ○ |
| P9-10 | Fault HDO acts selection in fault auto reset | 0: No action 1: Action | 0 | ○ |
| P9-11 | Fault auto reset interval | 0.1s ~ 100.0s | 1.0s | ○ |
| P9-12 | Input phase failure protection selection | 0: Disable 1: Enable | 0 | ○ |
| P9-13 | Output phase failure protection selection | 0: Disable 1: Enable | 1 | ○ |
| P9-14 | The first fault type | 0: No fault 1: Reserved 2: Acc over current 3: Dec over current 4: Over current in constant speed 5: Over voltage in Acc process 6: Over voltage in Dec process 7: Over voltage in constant speed 8: Reserved 9: Under voltage 10: Inverter overload 11: Motor overload 12: Input side phase failure 13: Output side phase failure 14: Module overheat 15: External fault 16: Communication fault 17: Contactor fault 18: Current detection fault 19: Motor autotuning fault 20: Encoder/PG card abnormal 21: Parameter R/W fault 22: Inverter hardware fault 23: Motor short circuit to ground fault 24: Reserved 25: Reserved 26: Running time arrival 27: Customized fault 1 28: Customized fault 2 29: Power-on time arrival 30: Off load 31: PID feedback lost when running 40: Fast current limiting over time 41: Reserved 42: Speed deviation oversize 43: Motor over speed | – | ● |
| P9-15 | The second fault type | Same as P9-14 | – | ● |
| P9-16 | The third (latest) fault type | Same as P9-14 | – | ● |
| P9-17 | Frequency at the third (latest) fault | – | – | ● |
| P9-18 | Current at the third (latest) fault | – | – | ● |
| P9-19 | Bus voltage at the third (latest) fault | – | – | ● |
| P9-20 | Input terminal's status at the third (latest) fault | – | – | ● |
| P9-21 | Output terminal's status at the third (latest) fault | – | – | ● |
| P9-22 | Inverter status at the third (latest) fault | – | – | ● |
| P9-23 | Power-on time at the third (latest) fault | – | – | ● |
| P9-24 | Running time at the third (latest) fault | – | – | ● |
| P9-27 | Frequency at the second fault | – | – | ● |
| P9-28 | Current at the second fault | – | – | ● |
| P9-29 | Bus voltage at the second fault | – | – | ● |
| P9-30 | Input terminal's status at the second fault | – | – | ● |
| P9-31 | Output terminal's status at the second fault | – | – | ● |
| P9-32 | Inverter status at the second fault | – | – | ● |
| P9-33 | Power-on time at the second fault | – | – | ● |
| P9-34 | Running time at the second fault | – | – | ● |
| P9-37 | Frequency at the first fault | – | – | ● |
| P9-38 | Current at the first fault | – | – | ● |
| P9-39 | Bus voltage at the first fault | – | – | ● |
| P9-40 | Input terminal's status at the first fault | – | – | ● |
| P9-41 | Output terminal's status at the first fault | – | – | ● |
| P9-42 | Inverter status at the first fault | – | – | ● |
| P9-43 | Power-on time at the first fault | – | – | ● |
| P9-44 | Running time at the first fault | – | – | ● |
| P9-47 | Action selection 1 for fault protection | Units place: motor overload (11) 0: Coast to stop 1: Dec-to-stop 2: Keep running Tens place: input phase failure (12) Hundreds place: output phase failure (13) Thousands place: external fault (15) Ten thousands place: communication fault (16) | 00000 | ○ |
| P9-48 | Fault protection action selection 2 | Units place: encoder/PG card fault 0: Coast to stop Tens place: function code R/W fault 0: Coast to stop 1: Dec-to-stop Hundreds place: reserved Thousands place: motor over heat (25) Ten thousands place: running time arrival (26) | 00000 | ○ |
| P9-49 | Fault protection action selection 3 | Units place: customized fault 1 (27) 0: Coast to stop 1: Dec-to-stop 2: Keep running Tens place: customized fault 2 (28) 0: Coast to stop 1: Dec-to-stop 2: Keep running Hundreds place: power-on time arrival (29) 0: Coast to stop 1: Dec-to-stop 2: Keep running Thousands place: off load (30) 0: Coast to stop 1: Dec-to-stop 2: Decelerate to 7% of motor rated power, then keep running; run at setting frequency when no off-load Ten thousands place: PID feedback lost when running (31) 0: Coast to stop 1: Dec-to-stop 2: Keep running | 00000 | ○ |
| P9-50 | Fault protection action selection 4 | Units place: speed deviation oversize (42) 0: Coast to stop 1: Dec-to-stop 2: Keep running Tens place: motor over speed (43) Hundreds place: initial place fault (51) | 00000 | ○ |
| P9-54 | Running frequency selection when fault | 0: Run at current running frequency 1: Run at setting frequency 2: Run at upper limit frequency 3: Run at lower limit frequency 4: Run at abnormal backup frequency | 0 | ○ |
| P9-55 | Abnormal backup frequency | 60.0% ~ 100.0% (100.0% corresponds to maximum frequency P0-10) | 100.0% | ○ |
| P9-56 ~ P9-58 | Reserved | – | – | ● |
| P9-59 | Instantaneous power-off action selection | 0: Invalid 1: Deceleration 2: Dec-to-stop | 0 | ○ |
| P9-60 | Recover judgment voltage when instantaneous power-off | 80 ~ 100.0% | 90.0% | ○ |
| P9-61 | Recover judgment time when instantaneous power-off | 0.00s ~ 100.00s | 0.50s | ○ |
| P9-62 | Action judgment voltage when instantaneous power-off | 60.0% ~ 100.0% (standard bus voltage) | 80.0% | ○ |
| P9-63 | Off-load protection selection | 0: Disable 1: Enable | 0 | ○ |
| P9-64 | Off-load detection level | 0.0 ~ 100.0% | 10.0% | ○ |
| P9-65 | Off-load detection time | 0.0 ~ 60.0s | 1.0s | ○ |
| P9-67 | Over speed detection value | 0.0 ~ 50.0% (maximum frequency) | 20.0% | ○ |
| P9-68 | Over speed detection time | 0.0s: no detection 0.1 ~ 60.0s | 1.0s | ○ |
| P9-69 | Speed deviation oversize detection value | 0.0 ~ 50.0% (maximum frequency) | 20.0% | ○ |
| P9-70 | Speed deviation oversize detection time | 0.0s: no detection 0.1 ~ 60.0s | 5.0s | ○ |
Słowa kluczowe
Micno KE600, lista parametrów, parameter list, P5–P9, wartość fabryczna, factory default, zakres nastaw, setting range
No comments to display
No comments to display